Recently, WORK PRO was in the last edition of ISE (Integration Systems Europe) along 9, 10, 11 and 12th of February, in Amsterdam (The Netherlands). ISE is one of the most important  international fair over the world, where the best companies and more than 65.000 professionals get in touch and catch up in this amazing meeting point.

WORK PRO was in ISE, and as previous editions, it was the perfect choice as showcase, to announce and show the novelties that along previous months the WORK PRO team was developing, designing and preparing, in order to present  every product for the meeting.

Some of the most important novelties presented at ISE  were the new series of SMART SPEAKERS, which consist of 3 models:

SCPRO A: Integrates a 2x20W amplifier, monitor output, bridge and dual modes.

SCPRO 4A BT: Presents the same features as SCPRO 4A, but adding Bluetooth connection.

SCPRO 4A BL: Presents Blueline integration (receiver), 2x6W amplifier, PoE supply, remote control (BLC1), bridge and dual modes.

The three models can be connected to 3 passive speakers in serial and can increase the number of speakers in the installation.

Also a new model of ceiling subwoofer was launched, the new C PRO 8 SUB, that completes the PURE PRO Series. Features as 160W Continuous @ 4? and 90 dB of sensitivity are part of this speakers, which completes and fits any installation as solution for a groovy and powerful sound.

Another novelty presented at ISE was the new outdoor speaker WFS 10 CX, a speaker made in fiberglass and IP 55 grade, totally weather resistant. This is a 2 way horn loaded loudspeaker, that provides high quality voice and music reproduction, thanks to it's high sensitivity 104 dB and 300 W Continuous @ 8?. The WFS 10 CX mounts a coaxial transducer, a 10"-inch cone LF driver and 1"-inch exit HF compression driver. Applications as athletic fields, arenas and race tracks, convention centres, swimming pools or fun parks are the best places where this new and innovative speaker can be installed. If you need more information, you can download from this link its datasheet.

The new pendant speaker WPS 310 was another novelty too, a characteristic speaker designed with style, made by fiberglass and mounting a 10" coaxial transducer (10"+1"), providing clear sound and high fidelity even under high power. It presents technical features as 500 W @ 8? and 95 dB of sensitivity. If you need more information about it, please find attach in this link its datasheet.

ISE was the perfect place where not just tje novelties were shown, the NEO Series where exposed there, like subwoofers or outdoor speakers. A complete set of solutions for any need.

As for the amplifier area, it was completely full of newness, 4 different models that complete the PA SERIES, all of them offering new solutions for installers and bringing new features as the PA 100 and PA 100 MX.

These new small amplifiers, fact wich does not make them weak, offer 100W that can operate with low impedance or 70/100V line loudspeakers. Booth of them are able to be controlled by remote control using RS485 protocol. The PA 100 MX  also, incorporates 3 Line inputs (2 rear + 1 front), microphone input, two tone controls (bass and treble), signal and peak led, and a knob for control the main volume level. If you need more information, you can read the following article regarding the mentioned amplifiers.

PA 1090 is a new multizone amplifier which integrates a large number of channels that can be operated low impedance channels as 70/100V line. Its 10 channels are distributed in the following way: 8 channels @ 4 ohm + 2 channels 70/100 V line. This versatility allows an amplified system centralized in a unique device, with different loudspeakers configurations, the low impedance channels can operate in bridge mode, making bigger the PA 1090 possibilities. The audio inputs are another example of this amplifier versatility, it disposes of 2 LINE inputs for all channels and 5 individual LINE inputs in order to connect several audio sources and to separate channels according to installations requirements. Also, the PA 1090 has protections against overheating (adding a fan with  speed  variations according to the temperature), overload and DC level.

As latest novelty, the MD 82 AX was one of the most interesting product. MD 82 AX is a mixer for microphones which integrates a large series of attractive features that allow the optimization of its installation and to outfit it with multiple audio signal control and management possibilities. This mixer incorporates 8 balanced inputs. It provides individual input level control and master level. The encoder in the frontal side allows to navigating through a configuration menu with different parameters on each channel. Among the functions to be performed, we can set three tone controls, low-pass and high-pass filters (with frequency adjustment) and 4 anti-feedback levels. All this information is showed in the LCD display. All inputs have switch to enable the connection of +48V phantom power supply microphones. The two features, that represent an interesting development, are the Auto-mixer functionality and the RS485 interface for external commands.